Dome 6 System

Solutions for all roof coverings. Clearly ballast-optimised system based on the latest wind tunnel standards.
  • Flat roof all-rounder - solutions for all roof coverings
  • Clearly ballast-optimised system based on the latest wind tunnel standards
  • Secure anchoring with fixed connection for roofs < 10° and low load reserves
  • Component-optimised system

System variant

  • 4 assembly steps for super-fast installation
  • Time-saving alignment of the rails with the Dome Speed Spacer gauge
  • Snap-in system for peaks and tool-free rail connectors
  • Flexible row spacing
  • Suitable for foil, bitumen, gravel and green roofs
  • Suitable for additional elevation on trapezoidal sheeting
  • For mounting on the long module side
  • For module sizes up to 2390 × 1170 mm
  • Based on Dome 6 Classic

Technical data

D-Dome 6.10 S-Dome 6.10
Scope of application Flat roofs < 10° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs Flat roofs < 10° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs
Fastening type/­roof fixture
  • Ballasted and no roof penetration for inclination: ≤ 3°
  • With fixed connection at inclination with Dome FixPro: > 3°
  • Ballasted and no roof penetration for inclination: ≤ 3°
  • With fixed connection at inclination with Dome FixPro: > 3°
Require­ments
  • Permissible module dimensions (L×W×H): 1448-2390 × 950-1170 × 30-50mm
  • Minimum system size D-Dome: 2 supports (4 modules)
  • Clamping at the short module side permitted (see module approvals…)
  • Permissible module dimensions (L×W×H): 1448-2390 × 950-1170 × 30-50mm
  • Minimum system size S-Dome: 2 modules
  • Clamping at the short module side permitted (see module approvals…)
Technical specifications Base rail
  • Dome 6 Xpress max. 16m
  • Classic 6/Classic 6 LS max. 12m
  • Dome 6 Xpress max. 15m
  • Classic 6/Classic 6 LS max. 12m
Technical specifications Module row
  • Dome 6 Xpress max. 16m
  • Classic 6/Classic 6 LS max. 16m
  • Dome 6 Xpress max. 15m
  • Classic 6/Classic 6 LS max. 15m
Minimum distance to the edge of the roof 600mm 600mm
Inclination angle 10° 10°
Material
  • Peak, SD, mounting rail, MidPlate, EndPlate, Connector, Porter, MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
  • Windbreaker: Magnelis
  • Mat S protective mat: EPDM
  • Small parts: stainless steel (1.4301) A2-70
  • Peak, SD, mounting rail, MidPlate, EndPlate, Connector, Porter, MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
  • Windbreaker: Magnelis
  • Mat S protective mat: EPDM
  • Small parts: stainless steel (1.4301) A2-70
Side views

Downloads

Product data sheet

Brochure - Flat roof systems

Assembly manual - D-Dome 6 Xpress + Classic

Assembly manual - D-Dome 6 Classic LS

Assembly manual - S-Dome 6 Xpress

Assembly manual - S-Dome 6 Classic

Assembly manual - S-Dome 6 Classic LS

Checklist - Flat roof

General Assembly and Maintenance Instructions

Certificate - Structural Analyses S-Dome 6.10

Certificate - Structural Analyses D-Dome 6.10

Module approval flat roof systems: Dome 6

Recommendations lightning protection and equipotential bonding

Protocol Static Friction (Coefficient of Friction)

TerraGrif - Potential equalisation